Home » FAQ( Page 5 )

Partner Center

YOU WILL GET WHAT YOU WANT HERE.

Login

FAQ

  • 【Hi-Q】How to do Hi-Q Project Post-Processing

    1.Run Hi-Net Server Software, Go to: Tools> Update with post diff result. 2.Mark on “use log file”, then click on “ change” to enter Post-Processing interface. 3.Import Base raw data and Rover raw data. Input the known point coordinates of Base station. 4.Click onselect, create a file name for the result file, and then click on calculate,wait for finished.The program would process and generate a post-processed file (*.log). 5. After processing finished, click on Add *.prj to import Hi-Q project; then click on load and update,the processed result would apply to the project.

  • 【SSCOM,V30】How to read IMEI number of V30?

    1.Open “SSCOM” software,choose right com port and Open port.
    2.Choose right parameter,baudrate 19200 etc.
    3.Click EXT.
    4.Click one by one to send all commands to V30.And then we get IMEI number of V30

  • 【Hi-RTK】How to import points into Hi-RTK?

    1.Prepare a *.txt file that contain the points details in a correct format.
    2.Click “Survey”and chose the point library you want.
    3.Then click the last second buttons at the bottom of interface.
    4.Make sure the points file was copied into your controller,find it out in a location/path.
    5.Choose the points file. Click OK.

  • 【PCC Radio,GM-xxPx management software】How to set PCC radio frequence?

    1.Switch on Receiver, set as UHF mode.
    2.Run “GM-xxPx management software” program, choose your COM Port and baud rate “19200” 3.Input the frequence, please click “Apply”.
    4.After get all the settings done, please click “Program” ,then wait for program finished.

  • 【V30 pro】How to open the voice prompt of V30 Pro?

    1.Open Hi-RTK software, connect the GPS of V30.
    2.After connecting GPS successfully, click Information->iRTK Setting->Set Irtk.
    3.Choose the language as you want, then restart the V30, then the voice opened finished.

  • 【Hi-RTK】How to export dxf and shp file from Hi-RTK?

    1.Open the Hi-RTK software.
    2.Click”Survey”to go to the interface.
    3.Click the “DXF” at the bottom of interface.
    4.Then click “Load” to chose dxf or shp file.

  • [ZTS320R]How to update firmware for new total station

    Use Hyper Terminal for update firmware.
    1.As for total station,go to fileman,then download.
    2.Input the pin code 82543,total station will shutdown.
    3.Run the Hyper Terminal,connect to total station when prompted.
    4.Update firmware by steps.

  • [ZTS320R]How to upgrade firmware for total station

    you must use Hyper Terminal to update firmware.
    1.As for total station,go to fileman,then download.
    2.Input the pin code 82543,total station will shutdown.
    3.Run the Hyper Terminal,connect to total station when prompted.
    4.Upgrade firmware by steps.

  • [ZTS320R]How to transfer data with windows software

    There are manual about the software to transfer the data.

  • [ZTS320R]series total station data transfer instructions

    1.Install driver of data transmission.
    2.Transmit data through RS232C communication line.
    3.Transmit data through the SD card.
    4.Transfer data through USB disk.
    5.Transfer data through MiniUSB communication cable.

  • [ZTS320R]How to calibrate triax for total station

    1.Level total station, put a reflector 30m forward.
    2.Switch on the instrument,turn on the laser.
    3.Aim at the center of the reflector.
    4.Remove the cover in the red frame below.
    5.Adjust the triax.
    6.Fix the cover back.

  • [HTS220R]How to check the configuration with 220R

    Please refer to relevant file below.

INFORMATION

Thank you for your interest in Hi-Target. We will contact you soon.